- Talk to an equipment specialist
Clean Energy Waste Oil Heaters
CONTACT US
Waste Oil Furnaces
CE - 140 WASTE OIL FURNACE
SMALL HEATER CREATES BIG SAVINGS, FOR UP TO 4,000 SQ. FT.The Clean Energy Heating Systems CE-140 Waste Oil Furnace is an entry level waste oil heater that’s perfect for a garage with 1 to 4 bays. With up to 140,000 BTU’s of heating output coupled to our innovative new design, it’s a very cost-effective way to heat smaller spaces.
Best of all, thanks to the CE-140’s ability to turn used motor oil, transmission fluid and other petroleum products into clean, safe heat, this waste oil furnace generates solid ROI while helping the environment.
In addition, all Clean Energy furnaces are engineered from the ground up to burn waste oils and comply with all EPA regulations. They easily install and provide for longer intervals between cleanings, and their low-profile design and flexible configuration is ideal for areas with limited ceiling height and other creative installation requirements.
Best of all, every Clean Energy waste oil furnace is built with our unique, patent-pending stainless steel heat exchanger and flue tubes. This next-generation design ensures long-lasting durability and highly efficient operation for years to come.
If you’re ready to start saving today, take advantage of No-Interest Financing, available for a limited time! Click here to request financing info.FEATURES & BENEFITS
- Stainless steel heat exchanger and flue tubes prevent rust and increase the life of the furnace
- Heat exchanger and flue tubes are designed to limit heat escape and maximize the heat produced
- Flue tubes are swedged, not welded, to resist cracking over years of heavy use
- Cleanout is easy, and with longer service intervals of 1,000+ hours, less frequent
- Over center latches allow easy cleanout without tools
- Digital, programmable burner control for reliable operation in all conditions
- Thermostatically-controlled pre-heater easily pass UL “cold oil start” tests
- Burns a variety of fuels including most synthetic oil, and just about any mixture of oil products
- Includes a pre-assembeld, vacuum-tested metering pump that does not require user adjustment
- Easy access oil line connector block allows servicing without disconnecting the oil line
- Extensive support network with dealers and distributors from coast to coast, as well as factory support
CE - 140 SPECIFICATIONS
- 140,000 BTU/hour Input
- 1,700/75°F, air flow output CFM/heat rise
- 1.0 GPH fuel consumption
- Acceptable fuels: used crankcase oil, transmission fluids, hydraulic oil, #2 heating oil (diesel fuel) and most synthetic oils
- 115vac, 60hz, single phase, 20A breaker
- High velocity air swept heat exchanger
- Vertical Stainless Steel flue tubes
- 6″ chimney outlets on left or right side
- Tank, wall or ceiling mountable
- 1,000 plus hour cleaning interval
- Digital wall thermostat
- 14,000 volt Burner with Interrupted Duty Ignition
- 77″l x 28″h x 26″w (w/burner and blower)
- 430 lbs hanging weight
- UL Listed
- cUL Listed
- 10 Year Warranty
- Made in the USA
Images, Drawings & Downloads
CE - 140
CE – 180 WASTE OIL FURNACE
Big Innovation in a Small Package, for up to 5,000 sq. ft.Our CE-180 Waste Oil Furnace is a strong performer for a 3 to 6 bay garage. With up to 175,000 BTU’s of output coupled to an innovative design, it’s a cost-effective and eco-friendly way to heat garages, workshops and other small to medium-sized spaces.
And thanks to its ability to turn used motor oil, transmission fluid and other petroleum products into clean, safe heat, the CE-180 generates solid ROI while helping the environment.
In addition, all Clean Energy furnaces are engineered from the ground up to burn waste oils and comply with all EPA regulations. They’re built to install easily and allow for longer cleaning intervals, and their low-profile design and flexible configuration is ideal for areas with limited ceiling height and other creative installation requirements.
Best of all, every Clean Energy furnace is built with our unique, patent-pending, heat exchanger and flue tubes. This innovation ensures long-lasting durability and highly efficient operation for years to come.
If you’re ready to start saving today, take advantage of No-Interest Financing, available for a limited time! Click here to request financing info.CE - 180 Features & Benefits
- Stainless steel heat exchanger and flue tubes prevent rust and increase the life of the furnace
- Heat exchanger and flue tubes are designed to limit heat escape and maximize the heat produced
- Flue tubes are swedged, not welded, to resist cracking over years of heavy use
- Cleanout is easy, and with longer service intervals of 1,000+ hours, less frequent
- Over center latches allow easy cleanout without tools
- Digital, programmable burner control for reliable operation in all conditions
- Thermostatically-controlled pre-heater easily pass UL “cold oil start” tests
- Burns a variety of fuels including most synthetic oil, and just about any mixure of oil products
- Includes a pre-assembeld, vacuum-tested metering pump that does not require user adjustment
- Easy access oil line connector block allows servicing without disconnecting the oil line
- Extensive support network with dealers and distributors from coast to coast, as well as factory support
CE – 180 Specifications
- 175,000 BTU/hour
- 1,700/80°F, air flow output CFM/heat rise
- 1.2 GPH fuel consumption
- Acceptable fuels: used crankcase oil, transmission fluids, hydraulic oil, #2 heating oil (diesel fuel) and most synthetic oils
- 115vac, 60hz, single phase, 20A breaker
- High velocity, stainless steel, air swept heat exchanger
- Vertical, stainless steel flue tubes
- 6″ chimney outlets on left or right side
- Tank, wall or ceiling mountable
- 1,000 plus hour cleaning interval
- Digital wall thermostat
- 14,000 volt Burner with Interrupted Duty Ignition
- 83″l x 28″h x 26″w
- UL Listed
- cUL Listed
- 10 Year Warranty
- Made in the USA
Images, Drawings & Downloads
CE – 180
CE – 250 WASTE OIL FURNACE
Big BTU’s & Big Innovation, for up to 7,000 sq. ft.Our CE-250 Waste Oil Furnace is a strong, eco-friendly furnace that’s been designed to efficiently heat a 5 to 8 bay garage. With up to 245,000 BTU’s of output and all of Clean Energy’s patent-pending design advances, it’s a powerful way to heat warehouses, garages and other large spaces that’s as eco-friendly as it is economical.
And thanks to its ability to run on used motor oil, transmission fluid and other petroleum products, the CE-250 makes economic and environmental sense for your business.
In addition, all of our waste oil furnaces are engineered from the ground up to burn used oils and comply with all EPA regulations. They’re designed for easy installation, longer cleaning intervals and flexible installation in areas with limited ceiling heights and other access requirements.
Best of all, every Clean Energy furnace is built with our patent-pending heat exchanger and flue tubes. This innovation ensures long-lasting durability and highly efficient operation for many years to come.
If you’re ready to start saving today, take advantage of No-Interest Financing, available for a limited time! Click here to request financing info.FEATURES & BENEFITS
- Stainless steel heat exchanger and flue tubes prevent rust and increase the life of the furnace
- Heat exchanger and flue tubes are designed to limit heat escape and maximize the heat produced
- Flue tubes are swedged, not welded, to resist cracking over years of heavy use
- Cleanout is easy, and with longer service intervals of 1,000+ hours, less frequent
- Over center latches allow easy cleanout without tools
- Digital, programmable burner control for reliable operation in all conditions
- Thermostatically-controlled pre-heater easily pass UL “cold oil start” tests
- Burns a variety of fuels including most synthetic oil, and just about any mixture of oil products
- Includes a pre-assembled, vacuum-tested metering pump that does not require user adjustment
- Easy access oil line connector block allows servicing without disconnecting the oil line
- Extensive support network with dealers and distributors from coast to coast, as well as factory support
CE - 250 Testimonials
- “The Clean Energy Heating Systems furnace just works, it’s hotter and easier to clean than the competitor’s furnace I replaced.” Troy, Town Service Center, Parkesburg, PA
CE – 250 Specifications
- 245,000 BTU/hour
- 2,700/90°F, air flow output CFM/heat rise
- 1.7 GPH fuel consumption
- Acceptable fuels: used crankcase oil, transmission fluids, hydraulic oil, #2 heating oil (diesel fuel) and most synthetic oils
- 115vac, 60hz, single phase, 30A breaker
- High velocity, stainless steel, air swept heat exchanger
- Vertical, stainless steel flue tubes
- 6″ chimney outlets on left or right side
- Tank, wall or ceiling mountable
- 1,000 plus hour cleaning interval
- Digital wall thermostat
- 14,000 volt Burner with Interrupted Duty Ignition
- 100″l x 28″h x 26″w
- UL Listed
- cUL Listed
- 10 Year Warranty
- Made in the USA
Images, Drawings & Downloads
CE – 250
CE - 330 WASTE OIL FURNACE
The Biggest Furnace & The Best Savings, for up to 9,000 sq. ft.The Clean Energy Heating Systems CE-330 Waste Oil Furnace is our largest heater, and is perfect for quickly and effectively heating a garage with 7 or more bays. With up to 325,000 BTU’s of output coupled to our innovative new furnace design, the CE-330 is truly a hot performer.
Thanks to the ability to turn used motor oil, transmission fluid and other petroleum products into clean, safe heat, the CE-330 waste oil heater generates solid ROI in addition to helping the environment.
Also, all Clean Energy furnaces are engineered from the ground up to burn waste oils and comply with EPA regulations. They easily install and provide for longer intervals between cleanings, and their low-profile design and flexible configuration is ideal for areas with limited ceiling height and other creative installation requirements.
Best of all, every Clean Energy waste oil heater is built with our unique, patent-pending heat exchanger and flue tubes. This design ensures long-lasting durability and highly efficient operation for years to come.
If you’re ready to start saving today, take advantage of No-Interest Financing, available for a limited time! Click here to request financing info.CE - 330 Features & Benefits
- Stainless steel heat exchanger and flue tubes prevent rust and increase the life of the furnace
- Heat exchanger and flue tubes are designed to limit heat escape and maximize the heat produced
- Flue tubes are swedged, not welded, to resist cracking over years of heavy use
- Cleanout is easy, and with longer service intervals of 1,000+ hours, less frequent
- Over center latches allow easy cleanout without tools
- Digital, programmable burner control for reliable operation in all conditions
- Thermostatically-controlled pre-heater easily pass UL “cold oil start” tests
- Burns a variety of fuels including most synthetic oil, and just about any mixture of oil products
- Includes a pre-assembled, vacuum-tested metering pump that does not require user adjustment
- Easy access oil line connector block allows servicing without disconnecting the oil line
- Extensive support network with dealers and distributors from coast to coast, as well as factory support
CE - 330 Waste Oil Furnace Specs
- 325,000 BTU/hour Input
- 3,700/85°F, air flow output CFM/heat rise
- 2.3 GPH fuel consumption
- Acceptable fuels: used crankcase oil, transmission fluids, hydraulic oil, #2 heating oil (diesel fuel) and most synthetic oils
- 230 vac, 60hz, single phase, 30A breaker
- High velocity, stainless steel, air swept heat exchanger
- Vertical, stainless steel flue tubes
- 8″ chimney outlets on the right or left side
- Tank, wall or ceiling mountable
- 1,000 plus hour cleaning interval
- Digital wall thermostat
- Burner with Interrupted Duty Ignition
- 111″l x 32″h x 26″w
- UL Listed
- cUL Listed
- 10 Year Warranty
- Made in the USA
Images, Drawings & Downloads
CE - 330
CE - 340 WASTE OIL BOILER
Our CE-340 Waste Oil Boiler brings cost-saving waste oil technology to hydronic heating systems. Featuring many of the same design innovations found in our line of waste oil furnaces, the CE-340 boiler allows businesses to create free hot water for radiant heat or other purposes by burning waste oil. It’s clean, safe and guaranteed to cut costs when compared to traditional boilers.
This next generation design features durable steel components, large-diameter flue tubes and a patented Clean Energy burner that turns used petroleum products into free heat. And as a high-mass/high-volume boiler system, it maintains a more consistent water temperature and more efficiently retains heat than other popular boilers.
Best of all, we’ve designed our CE-340 Waste Oil Boiler to be easy to install and maintain. Its front and back doors easily open for straight-through cleaning, while large, straight-through flue tubes reduce ash buildup and allow for a longer interval between cleanings.
If you’re ready to start saving today, take advantage of No-Interest Financing, available only until December 31, 2018! Click here to request financing info.CE-340 Features & Specifications
- Easy Clean out – Front and rear doors open for straight-through cleaning without removing stack
- Wet base fire tube boiler will reduce hot spots and deterioration
- ASME Certified
- Optional domestic hot water coil
- 2.4 GPH fuel flow rate
- 335,000 BTU/hr input (approx.)
- 275,000 BTU/hr output (approx.)
- 65 gallon boiler water volume
- Supply 2” NPT / Return 2” NPT
- 8” exhaust stack
- Requiring 2.5 CFM @ 25 PSI compressed air
- 115V / 60 Hz 20 AMP electric
- Boiler weight (dry) 1000 lbs.
- Standard relief valve setting 30 psi
- Heating surface 62 ft²
- Burner with Interrupted Duty Ignition
- UL and cUL Listed
Images, Drawings & Downloads
CE - 340
Buy a machine that can be serviced locally!!!
About Us
Founded in 1985, PSI Systems, Inc. has been Southern Colorado’s leader in commercial pressuring washing, parts washing, and wash water recycling, parts, service, and equipment. Learn More